|
 The DMST400 sectional overhead door is a range of high quality insulated and glazed doors. Available in various combinations of solid insulated sections, partially or fully glazed sections and an almost unlimited range of standard and optional colours.
Operation can be specified as simple manual push up, handchain operated or electrically operated with optional induction loops, traffic lights, safety edge, photocells, external pushbuttons or controlled access devices.
Utilising various track systems, the DMST400 can be installed as a standard lift up and over sectional door, vertical lift, pitched tracks, partial highlift and special low headroom for installations where maximum headroom is required.
Manufactured from high quality materials, all models are delivered complete with spring break devices and cable break devices for safety (if a spring or lift cable should fail, the door is prevented from falling to the ground by means of a secondary safety device), fully galvanised, heavy duty track system, vertical track side seals, top seal and bottom seal.
A built-in pass door can be fitted in the door of up to a maximum overall door width of 6000mm. The pass door profiles are fabricated from anodised aluminium. Dependent on the type of overhead door the pass door can be fitted with an electric security switch; this is mounted invisibly. All doors are individually manufactured to suit specific opening sizes and to meet the requirements of the latest European standards for safety.
SPECIFICATIONS:
All variants of the model DMST400 are manufactured to the following high specifications. Our use of only high quality materials is clear when viewing the completed installation. The rich lustre of both our standard and optional colours, smooth, quiet operation and bright finish to the track system, roller brackets, hinges and side profiles leave no doubt that this is a well designed, quality product which, with correct operation and routine maintenance will provide many years of reliable operation.
Panels:
610 mm deep x 40 mm thick composite panels manufactured using 0.5 thick hot dipped zinc coated (to BS EN 10147) steel internal and external facing sheets, each with a class 1 surface spread of flame when tested to BS 476: Part 7:1971. These sheets are bonded together using a CFC free foam with a density of 40kg/m3. The panel itself provides a ³U² value of 0.45 W/m2 K, this means that a typical 5000mm x 5000mm (w x h) door has a ŒU¹ value of 0.6 W/m2 K. A formed tongue and grooved section joint incorporating a neoprene seal running the full length of the panel provides excellent weather resistance. Standard finish - embossed primer coating to both sides, range of standard colours or factory painted to any RAL colour and oven baked. Special finishes are available for harsh environments (details on request).
Spring Assembly:
Sectional doors are counterbalanced to ensure the smooth running of doors, using minimal effort. All counterbalance spring calculations carried out by Door Maintenance Specialists Ltd ensure maximum life of the door springs, (most typical doors are calculated to a minimum 40,000 cycles).
The springs are high tensile helical wound steel which are heat treated for improved performance. The springs are mounted on a steel shaft supported by bearing brackets incorporating sealed bearing rollers, this ensures free running of the shaft. Also mounted on the spring shaft are the cable drums, these carry aircraft quality cables which have a 7:1 safety factor. The cables are looped and swaged using a hydraulic press to ensure the cables cannot become detached from the cable drums or the brackets which connect the cables to the bottom of the door panels. Spring break and cable break devices are standard features on all DMST400 models.
Track System:
The door tracks are galvanised steel 'J' type (designed to give free and easy running for bearing rollers). These are mounted on a galvanised steel jamb angle for fixing purposes and stud welded to ensure the most effective seal to the building as the tracks require adjustment on site.
Electric Operation:
Shaft mounted 3 phase plus neutral or single phase electric operator complete with manual over ride facility, built in limits and torque limiting dual safety system. Internal pushbutton for both open and close cycles. Optional safety edge installed into the bottom seal to stop and reverse the door should it strike an obstruction. Various additional options for traffic light control, remote, induction loop or card reader access.
|
1887 Leek Road Stoke on Trent, ST2 7AQ
Telephone/Fax: 01782 637 255
Email: service@dmsdoors.co.uk